RULES 2
PRO STOCK

CLASS DESCRIPTION

PRO STOCK is a for normally aspirated (no power adder) vehicles of all types with rear suspensions that may utilize ladder bar or four-links (no full tube chassis).. All entries will compete on a maximum 30X10.5 (non-W) slick. Super Stock type front-wheel drive conversions legal.

BALLAST:

Permanently attached ballast may be added in a NHRA legal manner. Removable

ballast for the purpose of classification adjustments is limited to 100 lbs. in a NHRA weight box.

BODY:

The car must retain its original appearance and profiles. Aftermarket fiberglass replacement panels are limited to hood, front fenders, doors, deck lid and bumpers. One piece front ends are permitted, but must retain factory un-altered grill and headlights

Front Grille:

Complete factory un-altered grille is required. Grilles may be covered, but with only clear tape or clear Lexan or Plexiglas, and must have prior approval from a WCHRA Official.

Rear Wing / Spoiler:

Aftermarket wings and spoilers are permitted, but may not extend more then 16 inches from the transition point with the body to the tip of the wing. Rear Wing "Spill Plates" does not have an exact size requirement, but must remain in the spirit of the PRO STOCK class (If your wing is questionable, notify the WCHRA before you enter a race)

FIREWALL:

Must retain in original factory location, and be constructed out of sheet-metal. Notching of factory firewall for valve cover clearance is allowed.

HOOD / SCOOPS:

Scoop or cowl may not exceed more than 9 inches at the highest point of the air inlet opening above the height of the original hood surface.

INTERIOR:

Dash board must be stock appearing and in stock location. Door panels must be covered or painted. Carpet and or upholstery is required to cover the flooring and tunnel where visible. Headliner is not required.

SEAT LOCATION:

Two front full size bucket seats, or one bench seat with upholstery required. Seats must remain in the stock location.

WINDOWS:

Must be of safety glass, Lexan, or other shatterproof materials, minimum 1/8th inch thick. Also must be clear and non hazy.

BRACKET RACING AIDS:

The use of bracket racing aids such as optical sensors, delay boxes, stutter boxes, and throttle stops are not allowed.

BRAKES:

The braking system may be upgraded to discs or larger drums. All cars must have front and rear brakes.

CHASSIS / SUSPENSION

FRONT SUBFRAME:

All sub framed or full framed cars must retain complete stock front subframe from firewall forward. Frame connectors or rear frame rails may not pass engine firewall, except for the following exceptions. The 62-67 Chevy II's and 64 1/2-68 Mustangs and similar cars with bolt-on front K-members, must retain stock or aftermarket bolt-on front subframe. The subframe must be a bolt on (not welded, unless kit is approved by WCHRA officials) to factory mounting location. Frame connectors or rear frame rails may pass firewall location, but not exceed where original front subframe mounts to the body. All late model Mustangs must retain factory front subframe from firewall forward. Stock or direct fit aftermarket K-members are permitted, but must be bolted in factory location using factory bolt holes. Cross members on all front sub frames may be altered or removed for oil pan clearance.

FRONT SUSPENSION:

All cars must retain stock suspension, aftermarket tubular control arms, coil over kits, or OEM front strut retrofits are permitted. But must be a direct bolt on, no welding modifications permitted. Aftermarket Racing Struts with spindle mounts or hub mounts designed for tube type front ends are prohibited. Stock wheelbase will be enforced on all vehicles.

DRIVE TRAIN

AUTOMATIC TRANSMISSIONS:

An automatic transmission originally produced by any American automobile manufacturer is permitted. Transmission-to-engine adapters are permitted. Aftermarket torque converter, trans-brake, shift kit, valve body, shifter, and pan cooler use are permitted.

MANUAL TRANSMISSION:

*Aftermarket Manual Transmissions (Clutchless Jericho versions are permitted) are allowed in Small Block applications only. Lenco, G-force & Liberty types, Clutchflites, or Clutch Hydros are not permitted. All shifts must be made manually without the aide of aftermarket electric or pneumatic devices.

REAR END:

Any rear end is allowed including Fab 9.Spools, aftermarket axles, and any gear

ratios are allowed.

ENGINE:

There is no limit for small blocks and a 555ci limit for big blocks. There are no

restrictions on internal engine modifications.

BLOCK:

Aftermarket iron or aluminum blocks are permitted.

EFI:

(Electronic Fuel Injection) Any EFI or digital fuel injection is permitted.

ENGINE MOUNTLOCATION:

The maximum allowable engine setback from the center line of the number-one spark-plug hole to the center line of the front spindle is 2 inches, except in those vehicles in which the engine was factory installed at a distance greater than 2 inches behind the spindle. In such cases, the engine set back may be no further back than the original location.

HEADS:

Two valves per cylinder maximum. One spark plug per cylinder maximum.

All billet cylinder heads prohibited.

INTAKE MANIFOLD:

No restrictions.* See add weight section.


EXHAUST:

Production type mufflers or collector type mufflers are required. No collector inserts permitted. Modification or removal of muffler internals is prohibited (no gutting).

FUEL / FUEL SYSTEMS:

Gasoline & Alcohol only (No Nitro) The WCHRA reserves the right to check gasoline at any time during competition. The addition of chemical additives intended to alter the makeup of the gasoline for increased performance is strictly prohibited. During fuel check, a competitor must identify the brand of gasoline being used. The sample will be considered illegal if it does not match the baseline results (ex. color, dielectric reading +or-.2, and chemical tests) logged by WCHRA. Failure to pass fuel check is grounds for disallowance of the run during competition and disqualification from the event during eliminations.

IGNITION:

No restrictions.

OILING SYSTEM:

Any oiling system is permitted. The front cross member may be altered for oil pan removal. Vacuum pumps are acceptable.

ON BOARD DIAGNOSTICS / DATA RECORDERS:

On board diagnostic computers and recorders are permitted. Memory and playback tachometers are allowed.

PARACHUTE:

Must meet NHRA requirements

RADIATOR:

An automotive-type radiator is required.

STEERING:

After market rack-and-pinion is allowed.

STREET LEGAL REQUIREMENTS:

All entries are required to have two working headlights and two working tail lights (headlight doors must be fixed open or work manually or automatically on cars so equipped). Brake lights, turn signals not required to operate.

TIRES:

Front tires must have a minimum tread width of 4.5 inches. Front tires do not have to be DOT approved. Rear tires must be a maximum 30X10.5 slick (non-W) *Hoosier tire, part number 18192D05 will not be allowed

PRO STOCK WEIGHT GUIDE:

(All weights are race-ready car with driver)

4 cyl ………………………….……….2300lbs

V/6's …………………………….……2400lbs

SMALL BLOCKS ……up to 356ci / 2500lbs

SMALL BLOCKS ....…357 - 400ci / 2600lbs

SMALL BLOCKS …....401 - 440ci / 2700lbs

SMALL BLOCKS ……......441 +ci / 2800lbs

BIG BLOCKS …….....up to - 500ci / 3100lbs

BIG BLOCKS ………...501 - 555ci / 3200lbs

ADD WEIGHT:

* 50lbs. for SB using a sheet metal, or any fabricated type intake manifold and or 2nd carburetor

* 100lbs for Small Blocks not using "True Wedge" or any "In-line Valve" Heads.

Example; YatesHighPort (part #'s 6049SC1 & 6049C3H) or any GM Symmetrical must add 100lbs.

* 150lbs. for manual trans (Clutch Version) in Small Blocks

* 200lbs. for manual trans (Clutchless Jericho) in Small Blocks

* 50lbs. for BB using a sheet metal, or any fabricated type intake manifold.

* 50lbs. for BB using a 2nd carburetor

* 50lbs. for BB with valve angle exceeding + or - 2 degrees from factory

(Dart 383 oval port or similar)

* 100lbs. For highly modified Big Block cylinder heads.

* 100lbs. For Big Block Ford C & E Motorsports Cylinder Head.

* 250lbs. For Big Blocks that use Big Chief, Big Duke, Pontiac, Olds, Ford C & E Profiler Cylinder Head or any Symmetrical and non conventional cylinder heads other then listed.

DEDUCT WEIGHT:

* 100lbs. For a 2-speed Automatic Transmission (Powerglide)

WHEEL BASE:

Must retain stock wheel base with a maximum variation from left to right and front to back of one inch.

WHEELIE BARS:

Wheelie bars permitted

wchra Required Decals:

Class Sponsor Decal

Sponsor decal must be installed on base of windshield on the passenger side. (Bottom left hand side when looking at front of vehicle windshield)

Series Sponsor Decal

Sponsor decal must be installed on base of windshield on the drivers side. (Bottom right hand side when looking at front of vehicle windshield)

Contingency Program & Contingency Decals:

In order to become eligible for WCHRA official contingency program, You must first become a member of the WCHRA. You can do this at the WCHRA Event Trailer during registration or on-line at the WCHRA Store. All contingency decals may appear anywhere on the windows in a clear and organized fashion. Contingency decals may not be overlapped or modified. Most decals are available at the WCHRA Event Trailer, but in the event the WCHRA does not have the decals in stock, it is the racer's responsibility to obtain the proper decals to be eligible for the Contingency payout.

RACE DAY POLICY'S

SCALES:

After each qualifying and elimination pass, all cars must stop and weigh at the track scales. If you lose in eliminations, and your opponent fails to make weight you will be reinstated into the eliminations only if you made minimum weight requirements. If both cars failed to make minimum weight, both cars will be disqualified. It is the driver's responsibility to verify with each track scale, the weight of his/her car prior to each race day. There will 5lb error factor allowed.

TOW BACK & TOW VEHICLES:

PRO STOCK does not allow tow vehicles of any sort in the staging lanes. All PRO STOCK vehicles must drive to scales and return to pits without the aide of any other vehicle.

BYE-RUNS:

All vehicles must take the tree, and run down the 1/4 mile.

All drivers and vehicles must meet current NHRA and track requirements.

For any other questions or more info on these rules please visit out website:

www.westcoasthotrod.com




DRAG RADIAL


Class Description:
Drag Radial is a heads-up class for any and all types of vehicles. This class is designed around a small Drag Radial Tire (275x60x15) Frame rails both front and rear must retain stock configuration, ladder bars are allowed but with a slight weight penalty. Any single power adder is allowed, including the use of a nitrous oxide, centrifugal or roots superchargers, and turbocharger combo's. Nitrous Controllers and Turbo Boost Controllers are permitted!

Class Guidelines:

BALLAST
Permanently attached ballast may be added in a NHRA legal manner. Removable ballast for the purpose of classification adjustments is limited to 100 lbs. in a NHRA weight box.

BODY
The car must retain its original appearance and profiles.

FIREWALL
Must retain factory unaltered firewall, in factory location. A cosmetic overlay is permitted.

INTERIOR
All factory interior pieces including pedal assemblies must be in factory locations. Factory door panels, headliner, carpet, dashboard are required. Back seat may be deleted, but must have carpet covering the bare floor.

SEAT LOCATION
Two front bucket seats, or one bench seat with upholstery required. Seats must remain in the stock location.

BRACKET RACING AIDS
The use of bracket racing aids such as optical sensors, delay boxes, and throttle
stops is prohibited.

BRAKES
The braking system may be upgraded to discs or larger drums, all cars must have front and rear brakes.

CHASSIS / SUSPENSION:

FRONT SUSPENSION
Suspension components must all remain in stock locations. Direct bolt-on A-arms are
permitted. Tubular K-members that are a direct bolt on are permitted. Vehicle must retain factory shock system (struts are only permitted on cars that came factory equipped. Sway bars may be removed. Bolt-on Front End kits are permitted.

K-MEMBER
Aftermarket factory-replacement-type K-member permitted, but must attach to the chassis using only the original factory OEM-type mounting bolts. No part of the K-member may be welded to the chassis.

REAR SUSPENSION

Bolt on traction devices are permitted. Leaf springs may be relocated for tire clearance purposes. Mini tubs are permitted, no full size wheel tubs will be allowed. Ladder Bar type Suspension will be legal (Rear frame rails must be in the stock location)
*Any car using rear coil shocks, will receive the ladder bar weight penalty.

FRAME & CHASSIS

Stock frame rails must be retained in stock locations (NO EXCEPTIONS) front and rear. Notching of rear frame rails for tire clearance is permitted. Sub frame connectors are permitted.

DRIVE TRAIN:

AUTOMATIC TRANSMISSIONS
Any OEM automatic transmission permitted. Aftermarket torque converter, shift kit, valve body, shifter, and pan cooler use are permitted. Trans brakes are permitted.

MANUAL TRANSMISSION

After-market clutch (single disc only) assisted manual transmissions are allowed Clutch/Automatics or planetary transmissions are not allowed. Split sliders are also not allowed. All shifts must be made manually without the aid of electric, hydraulic or pneumatic devices. Any manual transmission built by an automotive manufacturer, with stock case and gears will race at same weight as an automatic transmission entry.

REAR END

Any factory type rear end is allowed.

ELECTRICAL
The battery may be relocated.

ENGINE

No cubic inch limits.

ENGINE BLOCK

Aftermarket Cast Iron & Aluminum production blocks are allowed.

CAMSHAFT
Any camshaft allowed

CARBURETOR / THROTTLE BODY

Any single or dual carburetor or throttle body set-up is allowed

EFI
Any EFI system is permitted

ENGINE MOUNT LOCATION

Engine must remain in stock location. Engine may not touch the factory unaltered firewall. Motor plates are permitted.

NITROUS
Any nitrous combo is legal, but cannot be used with any other power adder. Controllers/Progressive units are permitted!

SUPERCHARGER / TURBOCHARGER

Any Supercharger (Roots/671-F3 centrifugal or equivalent) or Turbocharger (up to twin/72mm and single/98mm) is permitted. Turbo units will be measured Tip to Tip. Boost Controllers are permitted

EXHAUST
Production type mufflers or collector mufflers are required. Modification or removal of muffler internals is prohibited (no gutting).

IGNITION
No restrictions

OILING SYSTEM

No Restrictions.

ON BOARD DIAGNOSTICS / DATA RECORDERS
On board diagnostic computers and recorders are permitted. Memory and playback tachometers are allowed.

RADIATOR
An automotive-type radiator is required.

STEERING
Rack and Pinion allowed on all vehicles.

STREET LEGAL REQUIREMENTS
All cars are required to have working headlights and tail lights (headlights doors must be fixed open or work manually or automatically on cars so equipped). Brake lights, turn signals are required.

TIRES
Front tires must have a minimum tread width of 4.5 inches. Front tires do not have to be DOT approved. Rear Tires...maximum 275x60x15 Drag Radial Tire ONLY!!!!!

WHEEL BASE

Must retain stock wheel base with a maximum variation right to left and front to back of one inch.

WHEELIE BARS

Wheelie bars are strictly prohibited.

weight guide

Base Weight (All weights are race-ready, car with driver)
V/6 W/Nitrous....................................................... 2700 lbs
V/6 W/Turbo or Blower............................................ 2800 lbs
Small Blocks W/Nitrous......................................... 2800 lbs
Small Blocks W/Single Turbo or Blower................... 3450 lbs
Big Blocks W/Nitrous............................................. 3250 lbs
Big Blocks W/Turbo Or Blower................................. 3450 lbs


WEIGHT ADDS & BREAKS:

NITROUS COMBOS
*Add 50 lbs. for SBF Victor 2 or Pro King

*Add 100 lbs. for small blocks using YatesHighPort (part #'s 6049SC1 & 6049C3H), Brodix "Neal" or GM symmetrical Cylinder heads

*Add 50lbs. for BB with valve angle exceeding + or - 2 degrees from factory

(Dart 383 oval port or similar)

*Add 200 lbs. for Big Blocks that use Big Chief, Pontiac, Olds, Ford, C & E "Motorsports"or "ProFiler" or any symmetrical and non conventional cylinder heads other then listed.

ALL CARS
*
Add 100 lbs. for Ladder Bars and or Coil Over Rear Suspension.

DEDUCTS

*Deduct 400 lbs. for no Power Adder.

WCHRA Required Decals
Class Sponsor Decal
Sponsor decal must be installed on base of windshield on the passenger side. (Bottom left hand side when looking at front of vehicle windshield)
EventSponsor Decal

Sponsor decal must be installed on base of windshield on the drivers side. (Bottom right hand side when looking at front of vehicle windshield)
Decals will be available during registration at the WCHRA Event Trailer

Contingency Program & Contingency Decals
In order to become eligible for WCHRA official contingency program, You must be a member of the WCHRA. You can do this at the WCHRA Event Trailer during registration or on-line at the WCHRA Store. It is the racer's responsibility to obtain the proper decals from the WCHRA or the Manufacturer to be eligible for the contingency payout. All contingency decals may appear anywhere on the windows in a clear and organized fashion. Contingency decals may not be overlapped or modified.

RACE DAY POLICY'S

SCALES
After each qualifying and elimination pass, all cars must stop and weigh at the track scales. If you lose in eliminations, and your opponent fails to make weight you will be reinstated into the eliminations only if you made minimum weight requirements. If both cars failed to make minimum weight, both cars will be disqualified. It is the driver's responsibility to verify with each track scale, the weight of his/her car prior to each race day. There will 5lb error factor allowed.

TOW BACK & TOW VEHICLES
Drag Radial entries are NOT allowed to tow to staging lanes and/or to the track scales with a golf cart or other similar small tow vehicle.

BYE-RUNS

All vehicles must take the tree, and run down the 1/4 mile.

All drivers and vehicles must meet current NHRA and track requirements.

For any other questions or more info on these rules please visit out website:

www.westcoasthotrod.com




7.60/A GAS

Class Description:

7.60 /A GAS is based on an 7.60 index (all runs made faster than the index will be disqualified) unless the run is made in eliminations and both cars break out, then the closest car to 7.60 will be declared the round winner and advance to the next round. "Door Cars Only" are welcome to try out this class.

Class Guidelines

Rules & Regulations:

7.60/A GAS uses a "4/10ths Pro Tree" start system and will utilize a Sportsman ladder for pairings. Index offers an "All Run" field, so everyone will make it to elimination day!!! "Door slammer-type" vehicles only are permitted/no dragsters. Any and all performance modifications are legal, no minimum weight requirements, and all power adders are accepted. Trans-brakes and 3-steps will be allowed. No downtrack rev-limiters.

Qualifying:

All 7.60/A GAS cars will receive 3 qualifying runs on Saturday. #1 Qualifier will be determined by the closest run to the 7.60 index without going quicker. In the event of 2 or more cars running the same qualified ET, the driver who posts the time first will be awarded with the qualified spot. If you run quicker than the 7.60 Index on all 3 runs, you will be placed at the bottom of the ladder for eliminations.

ELECTRONIC POLICY FOR 7.60/A GAS:

Electronic driving devices are strictly prohibited in this class. Items that constitute electronic driving devices include, but are not limited to, throttle stops, delay boxes & cross-over boxes. All such devices must be removed from the car before passing tech inspection. Rev-limiters are allowed, but three-step control is the maximum permitted. No downtrack rev-limiters. If you have a Delay Box or any Bracket Racing Aide Hooked up in your vehicle, don't bother entering 7.60/A GAS!!!

Deep Staging:

Deep staging is permitted. Please have the words "DEEP" clearly written on all four windows.

Burn-Out Procedure:

In 7.60/A GAS burn-outs across the starting line are allowed. You must complete and stop your burn-out within a reasonable manner as to not delay the other driver or event continuation.

WCHRA Required Decals:

Class Sponsor Decal

Sponsor decal must be installed on base of windshield on the passenger side. (Bottom left hand side when looking at front of vehicle windshield)

Series Sponsor Decal

Sponsor decal must be installed on base of windshield on the driver’s side. (Bottom right hand side when looking at front of vehicle windshield)

Contingency Program & Contingency Decals:

In order to become eligible for WCHRA official contingency program, you must first become a member of the WCHRA. You can do this at the WCHRA Event Trailer during registration or on-line at the WCHRA Store. All contingency decals may appear anywhere on the vehicle in a clear and organized fashion. Contingency decals may not be overlapped or modified. Most decals are available at the WCHRA Event Trailer, but in the event the WCHRA does not have the decals in stock, it is the racer's responsibility to obtain the proper decals to be eligible for the Contingency payout.

WCHRA Point System:

We will be calculating points at each event, and will crown a champion at the conclusion of the season.

WCHRA Race Day Rules and Procedures

Tow Vehicles:

7.60/A GAS allow 1 tow vehicle per car in the staging/safety lanes. You can tow your vehicle back to the pits at the conclusion of your run after exiting the racing surface and after scales.

All drivers and vehicles must meet current NHRA and track requirements.

For questions or more information on these rules please visit the website:

www.westcoasthotrod.com



8.60/B GAS

Class Description:

8.60 /B GAS is based on an 8.60 index (all runs made faster than the index will be disqualified) unless the run is made in eliminations and both cars break out, then the closest car to 8.60 will be declared the round winner and advance to the next round. "Door Cars Only" are welcome to try out this class.

Class Guidelines

Rules & Regulations:

8.60/B GAS uses a "4/10ths Pro Tree" start system and will utilize a Sportsman ladder for pairings. Index offers an "All Run" field, so everyone will make it to elimination day!!! "Door slammer-type" vehicles only are permitted/no dragsters. Any and all performance modifications are legal, no tire size limits (Slicks OK), no minimum weight requirements, and all power adders are accepted. Trans-brakes and 3-steps will be allowed. No downtrack rev-limiters.

Qualifying:

All 8.60/B GAS cars will receive 3 qualifying runs on Saturday. #1 Qualifier will be determined by the closest run to the 8.60 index without going quicker. In the event of 2 or more cars running the same qualified ET, the driver who posts the time first will be awarded with the qualified spot. If you run quicker than the 8.60 Index on all 3 runs, you will be placed at the bottom of the ladder for eliminations.

ELECTRONIC POLICY FOR 8.60/B GAS:

Electronic driving devices are strictly prohibited in this class. Items that constitute electronic driving devices include, but are not limited to, throttle stops, delay boxes & cross-over boxes. All such devices must be removed from the car before passing tech inspection. Rev-limiters are allowed, but three-step control is the maximum permitted. No downtrack rev-limiters. If you have a Delay Box or any Bracket Racing Aide Hooked up in your vehicle, don't bother entering 8.60/B GAS!!!

Deep Staging:

Deep staging is permitted. Please have the words "DEEP" clearly written on all four windows.

Burn-Out Procedure:

In 8.60/ B GAS burn-outs across the starting line are allowed. You must complete and stop your burn-out within a reasonable manner as to not delay the other driver or event continuation.

WCHRA Required Decals:

Class Sponsor Decal

Sponsor decal must be installed on base of windshield on the passenger side. (Bottom left hand side when looking at front of vehicle windshield)

Series Sponsor Decal

Sponsor decal must be installed on base of windshield on the driver’s side. (Bottom right hand side when looking at front of vehicle windshield)

Contingency Program & Contingency Decals:

In order to become eligible for WCHRA official contingency program, you must first become a member of the WCHRA. You can do this at the WCHRA Event Trailer during registration or on-line at the WCHRA Store. All contingency decals may appear anywhere on the vehicle in a clear and organized fashion. Contingency decals may not be overlapped or modified. Most decals are available at the WCHRA Event Trailer, but in the event the WCHRA does not have the decals in stock, it is the racer's responsibility to obtain the proper decals to be eligible for the Contingency payout.

WCHRA Point System:

We will be calculating points at each event, and will crown a champion at the conclusion of the season.

WCHRA Race Day Rules and Procedures

Tow Vehicles:

8.60/B GAS does not allow tow vehicles of any sort in the staging lanes. You can tow your vehicle back to the pits at the conclusion of your run after exiting the racing surface

All drivers and vehicles must meet current NHRA and track requirements.

For questions or more information on these rules please visit the website:

www.westcoasthotrod.com






9.60/C GAS


Class Description:

9.60/C GAS is based on an 9.60 index (all runs made faster than the index will be disqualified) unless the run is made in eliminations and both cars break out, then the closest car to 9.60 will be declared the round winner and advance to the next round. Any race car that meets current NHRA rules is welcome to try this class.

Class Guidelines

Rules & Regulations:

9.60/C GAS uses a "4/10ths Pro Tree" start system and will utilize a Sportsman ladder for pairings. 9.60/ C GAS offers an "All Run" field, so everyone will make it to elimination day!!! Any and all performance modifications are legal, no tire size limits (Slicks OK), no minimum weight requirements, and all power adders are accepted. Trans-brakes and 3-steps will be allowed. No downtrack rev-limiters.

Qualifying:

All 9.60/C GAS cars will receive 3 qualifying runs on Saturday. #1 Qualifier will be determined by the closest run to the 9.60 index without going quicker. In the event of 2 or more cars running the same qualified ET, the driver who posts the time first will be awarded with the qualified spot. If you run quicker than the 9.60 index on all 3 runs, you will be placed at the bottom of the ladder for eliminations.

ELECTRONIC POLICY FOR 9.60/C GAS:

Electronic driving devices are strictly prohibited in this class. Items that constitute electronic driving devices include, but are not limited to, throttle stops, delay boxes & cross-over boxes. All such devices must be removed from the car before passing tech inspection. The driver must accomplish all driving functions, (not electronics). All on-track tuning of fuel, throttle, clutch, transmission, and ignition systems must be a direct function of the driver. Data recorders are allowed for data acquisition only and in no way may be able to make a control function that enhances the drivers or tuners ability to control the performance of the car while it is on the track. No microprocessor feedback controlled ignition systems allowed. Rev-limiters are allowed. Two-step controllers are allowed. Rev-limiters are allowed, but three-step control is the maximum permitted. No downtrack rev-limiters.If you have a Delay Box or any Bracket Racing Aide Hooked up in your vehicle, don't bother entering 9.60/C GAS

Deep Staging:

Deep staging is permitted. Please have the words "DEEP" clearly written on all four windows.

Burn-Out Procedure:

9.60/C GAS does not allow burn-outs across the starting line. You must complete and stop your burn-out without crossing the starting line.

WCHRA Required Decals:

Class Sponsor Decal

Sponsor decal must be installed on base of windshield on the passenger side. (Bottom left hand side when looking at front of vehicle windshield)

Series Sponsor Decal

Sponsor decal must be installed on base of windshield on the driver’s side. (Bottom right hand side when looking at front of vehicle windshield)

Contingency Program & Contingency Decals:

In order to become eligible for WCHRA official contingency program, You must first become a member of the WCHRA. You can do this at the WCHRA Event Trailer during registration or on-line at the WCHRA Store. All contingency decals may appear anywhere on the vehicle in a clear and organized fashion. Contingency decals may not be overlapped or modified. Most decals are available at the WCHRA Event Trailer, but in the event the WCHRA does not have the decals in stock, it is the racer's responsibility to obtain the proper decals to be eligible for the Contingency payout.

WCHRA Point System:

We will be calculating points at each event, and will crown a champion at the conclusion of the season.

WCHRA Race Day Rules and Procedures

Tow Vehicles:

9.60/C GAS does not allow tow vehicles of any sort in the staging lanes. You can drive your vehicle back to the pit area.

All drivers and vehicles must meet current NHRA and track requirements.

For questions or more information on these rules please visit the website:

www.westcoasthotrod.com


10.60/D GAS

Class Description:

10.60 /D GAS is based on an 10.60 index (all runs made faster than the index will be disqualified) unless the run is made in eliminations and both cars break out, then the closest car to 10.60 will be declared the round winner and advance to the next round. "Door Cars Only" are welcome to try out this class.

Class Guidelines

Rules & Regulations:

10.60/D GAS uses a "4/10ths Pro Tree" start system and will utilize a Sportsman ladder for pairings. Index offers an "All Run" field, so everyone will make it to elimination day!!! "Door slammer-type" vehicles only are permitted/no dragsters. Any and all performance modifications are legal, no tire size limits (Slicks OK), no minimum weight requirements, and all power adders are accepted. Trans-brakes and 3-steps will be allowed. No downtrack rev-limiters.

Qualifying:

All 10.60/D GAS cars will receive 3 qualifying runs on Saturday. #1 Qualifier will be determined by the closest run to the 10.60 index without going quicker. In the event of 2 or more cars running the same qualified ET, the driver who posts the time first will be awarded with the qualified spot. If you run quicker than the 10.60 Index on all 3 runs, you will be placed at the bottom of the ladder for eliminations.

ELECTRONIC POLICY FOR 10.60/D GAS:

Electronic driving devices are strictly prohibited in this class. Items that constitute electronic driving devices include, but are not limited to, throttle stops, delay boxes & cross-over boxes. All such devices must be removed from the car before passing tech inspection. Rev-limiters are allowed, but three-step control is the maximum permitted. No downtrack rev-limiters. If you have a Delay Box or any Bracket Racing Aide Hooked up in your vehicle, don't bother entering 10.60/D GAS!!!

Deep Staging:

Deep staging is permitted. Please have the words "DEEP" clearly written on all four windows.

Burn-Out Procedure:

10.60/ D GAS does not allow burn-outs across the starting line. You must complete and stop your burn-out without crossing the starting line.

WCHRA Required Decals:

Class Sponsor Decal

Sponsor decal must be installed on base of windshield on the passenger side. (Bottom left hand side when looking at front of vehicle windshield)

Series Sponsor Decal

Sponsor decal must be installed on base of windshield on the drivers side. (Bottom right hand side when looking at front of vehicle windshield)

Contingency Program & Contingency Decals:

In order to become eligible for WCHRA official contingency program, You must first become a member of the WCHRA. You can do this at the WCHRA Event Trailer during registration or on-line at the WCHRA Store. All contingency decals may appear anywhere on the vehicle in a clear and organized fashion. Contingency decals may not be overlapped or modified. Most decals are available at the WCHRA Event Trailer, but in the event the WCHRA does not have the decals in stock, it is the racer's responsibility to obtain the proper decals to be eligible for the Contingency payout.

WCHRA Point System:

We will be calculating points at each event, and will crown a champion at the conclusion of the season.

WCHRA Race Day Rules and Procedures

Tow Vehicles:

10.60/D GAS does not allow tow vehicles of any sort in the staging lanes. You can tow your vehicle back to the pits at the conclusion of your run after exiting the racing surface

All drivers and vehicles must meet current NHRA and track requirements.

For questions or more information on these rules please visit the website:

www.westcoasthotrod.com

GoDaddy.com