|
|
|
|
back
DRAG RADIAL
DRAG RADIAL(275`S)
KOPP`S Speed Shop/TEC Services
Entry Fee................... $ 125 WINNER.................... $ 1800 R/U .................... $ 500 SEMI .................... $ 150 #1 Qualifier................ $ 100 *************************************************************************************************** Tech............................ 50 points Qualifying The #1 Qualifier will always earn 10 points more than 2nd. Example...8 car field #1................................ 17 points #2................................ 7 points #3................................ 6 " #4................................ 5 " #5................................ 4 " #6................................ 3 " #7................................ 2 " #8................................ 1 "
Each Round...................... 20 points(Must take Tree!) Winner........................... 20 points
E.T. Record...................... 20 points MPH Record..................... 10 points *************************************************************************************************** CLASS DESCRIPTION:
Drag Radial is a heads-up class for any and all types of vehicles. This class is designed around a small Drag Radial Tire (275x60x15) Frame rails both front and rear must *retain stock configuration, ladder bars are allowed but with a weight penalty. Any single power adder is allowed, including the use of a nitrous oxide, centrifugal or roots superchargers and turbocharged combo's. Nitrous and Boost Controllers are permitted!**Rear Wheel Drive Only** ***Drag Radial will be run in the 1/8th Mile***
CLASS GUIDELINES:
BALLAST:
Permanently attached ballast may be added in a NHRA legal manner. Removable ballast for the purpose of classification adjustments is limited to 100 lbs. in an NHRA weight box.
BODY:
The car must retain its original appearance and profiles. Aftermarket fiberglass replacement panels are limited to; hood, hood scoop, fenders,doors, deck lids and bumpers.One piece front-ends are allowed (Hood must be separate) and must retain factory grill,head lights, and marker lights.Aftermarket wings and spoilers are permitted,but may not extend more than 10 inches from the transition point with the body to the tip.The driver and passenger doors must open from inside and outside.Lexan Windows are Permitted but must be Stock Appearing ! Maximum allowed Front overhang is 45" Max measured from Front axle centerline to forward most part of vehicle.
FIREWALL:
Must retain factory unaltered firewall, in factory location. A cosmetic overlay is permitted.
INTERIOR:
Door panels, headliner(Prefered), carpet, dashboard are required. Back seat may be deleted, but must have carpet covering the bare floor.
SEAT LOCATION:
Two front bucket seats, or one bench seat with upholstery required. Seats must remain in the stock location.
BRACKET RACING AIDS:
The use of "Reaction Time Devices" Optical Sensors, Delay Boxes, etc, is prohibited!
BRAKES:
The braking system may be upgraded to discs or larger drums, all cars must have front and rear brakes.
CHASSIS / SUSPENSION:
FRONT SUSPENSION:
Suspension components must all remain in stock locations. Direct bolt-on A-arms are permitted. Tubular K-members that are a direct bolt on are permitted. Vehicle must retain factory shock system (struts are only permitted on cars that came factory equipped). Sway bars may be removed.Aftermarket Bolt-on Front End kits that use a strut to replace an a-arm type suspension for early Nova/Chevy II`s / Mustangs,etc..are permitted (Chris Alston, Smith Racecraft, Fat Man,Heidts, Scotts Hot Rods, T.C.I., etc..)
K-MEMBER:
Aftermarket factory-replacement-type K-member permitted, but must attach to the chassis using only the original factory OEM-type mounting bolts. No part of the K-member may be welded to the chassis.
REAR SUSPENSION:
Bolt on traction devices are permitted. Leaf springs may be relocated for tire clearance purposes.Mini tubs are permitted, no full size wheel tubs will be allowed. Ladder Bar type Suspension will be legal with a weight penalty. (Ladder Bar Car Rear frame rails may be notched or sectioned, No Back-Half) Vehicles using rear coil-over shocks(With springs attached to the shocks), will receive ladder bar weight add of 100lbs
FRAME & CHASSIS:
Stock frame rails must be retained in stock locations front and rear. Notching of rear frame rails for tire clearance is permitted. Sub frame connectors are permitted.
DRIVE TRAIN:
AUTOMATIC TRANSMISSIONS:
Any OEM automatic transmission permitted. Aftermarket torque converter, shift kit, valve body,shifter, and pan cooler are permitted. Trans brakes O.K.
MANUAL TRANSMISSION:
After-market clutch (single disc only) assisted manual transmissions are allowed. Clutch/Automatics or planetary transmissions are not allowed. Split sliders are also not allowed.All shifts must be made manually without the aid of electric, hydraulic or pneumatic devices. Any manual transmission built by an automotive manufacturer, with stock case and gears will race at same weight as an automatic transmission entry.
EFI:
Any EFI system is permitted
ENGINE:
Cross-Breeding is O.K.
ENGINE BLOCK:
Aftermarket Cast Iron & Aluminum blocks are allowed.
ENGINE MOUNT LOCATION:
Engine must remain in stock location. Engine may not touch the factory unaltered firewall. **Motor plates are permitted**
CARBURETOR / THROTTLE BODY:
Any single or dual carburetor or throttle body set-up is allowed
NITROUS OXIDE:
All nitrous systems are allowed. Nitrous oxide commercially available, thermostatically controlled blanket-type warmer accepted. Any other external heating of bottles prohibited.The use of any agents other than nitrous oxide as part of, or mixed with, this pressurized fuel system is prohibited. If an entry is presented to tech as a non-nitrous weight break, all nitrous oxide lines,fittings, solenoids, and bottles must be removed before car is allowed to pass tech.
SUPERCHARGER / TURBOCHARGER:
Supercharger limited to 12-71 for Roots**Screw Superchargers are not allowed** Centrifugal Superchargers F-3R or Equivalent/ Max Turbocharger Twin 80mm or Single 106mm allowed.Turbochargers are limited to a maximum size of (80mm or 106mm).All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas or any other substance into the inlet or exhaust housing is prohibited. ***Turbochargers will be measured at the inlet housing.***
EXHAUST:
Production type mufflers or collector mufflers are required. Modification or removal of muffler internals is prohibited. (no gutting).
FUEL / FUEL SYSTEMS:
Gasoline ONLY!. The WCHRA reserves the right to check gasoline at any time during competition.Failure to pass fuel check is grounds for disallowance of the run during competition and disqualification from the event during eliminations.
IGNITION:
No restrictions
OILING SYSTEM:
No Restrictions.
ON BOARD DIAGNOSTICS / DATA RECORDERS:
On board diagnostic computers and recorders are permitted. Memory and playback tachometers are allowed.
RADIATOR:
Functional cooling system required.
STEERING:
Rack and Pinion allowed on all vehicles.
STREET LEGAL REQUIREMENTS:
All cars are required to have working headlights and tail lights (headlights doors must be fixed open or work manually or automatically on cars so equipped). Brake lights, turn signals are (Prefered).
TIRES:
Front tires must have a minimum tread width of 4.5 inches. Front tires do not have to be DOT approved. Rear Tires...maximum 275x60x15 Drag Radial Tire
WHEEL BASE:
Must retain stock wheel base with a maximum variation right to left and front to back of one inch.
WHEELIE BARS:
Wheelie bars are strictly prohibited.
*************************************************************
WEIGHT GUIDE:
Base Weight (All weights are race-ready, car with driver)
4 CYL/Rotary W/ Any Power Adder................................................ 2200 lbs V/6 W/Nitrous....................................................................... 2500 lbs V/6 W/Turbo or Blower..............................................................2800 lbs Small Blocks W/Nitrous..............................................................2800 lbs Small Blocks W/Turbo or Blower(Up to 330c.i.)...................................3300 lbs Small Blocks W/Turbo or Blower(331-470 c.i.)....................................3400 lbs Big Blocks W/Nitrous (499 c.i. & Smaller).........................................3100 lbs Big Blocks W/Nitrous (500 c.i.-599 c.i.)...........................................3200 lbs Big Blocks W/Nitrous (600 c.i. & Bigger)..........................................3300 lbs Big Blocks W/Turbo Or Blower( 600 c.i. Max) LIMITED to CONVENTIONAL HEADS ONLY !!.......................................3500 lbs
WEIGHT ADDS:
SB Ford Edelbrock VictorII ,CFE Pro King or SB Chevy 12*or14*Pro Action *Does not include OEM Production Cyl. Heads*................................ADD 50 lbs
Small Blocks not using "True Wedge" or any "In-line Valve" Heads/ (Edelbrock/Yates HighPort part #'s 6049SC1 & 6049C3H) or similar/GM Symmetrical/Splayed valve...............................................................................ADD 100 lbs
Ladder Bars and/or Coil Over Shocks..........................................ADD 100 lbs
Big Blocks using Big Chief, Big Duke, Pontiac, Olds, Ford C & E Profiler Cylinder Head or any similar Symmetrical/ Non-Conventional Cylinder Heads...................................................................ADD 150 lbs
DEDUCTS: Normally Asperated/N20 Combos W/Single Carb/TB..................DEDUCT 50 lbs
Normally Aperated/N20 Combos W/ Cast intake.......................DEDUCT 50 lbs
Turbo/SC combos running gasoline without an intercooler............DEDUCT 100 lbs
Vehicles using: ProCharger/ ATI D-1,D-1SC,D-1R,F1,F1A,F1C,F1R,F2 Vortech A thru T-trim/Up to YS & YSI & X Trim PAXTON NOVI-1000,2000 Or Equivalents, Single 98/twin 72MM..or Smaller Turbos................................DEDUCT 100 lbs
Normally Aspirated Combos(No Power Adder)...........................DEDUCT 400 lbs
****************************************************************************************************
WCHRA REQUIRED DECALS:
CLASS SPONSOR DECAL:
Sponsor decal must be installed on base of windshield on the passenger side. (Bottom left hand side when looking at front of vehicle windshield)
SERIES SPONSOR:
Sponsor decal must be installed on base of windshield on the driver’s side. (Bottom right hand side when looking at front of vehicle windshield)
EVENT SPONSOR DECAL:
Sponsor decal must be installed on base of windshield on the drivers side. (Bottom right hand side when looking at front of vehicle windshield) Decals will be available during registration at the WCHRA Event Trailer
CONTINGENCY DECALS:
All contingency decals may appear anywhere on the windows in a clear and organized fashion.Contingency decals may not be overlapped or modified. Most decals are available at the WCHRA Event Trailer, but in the event the WCHRA does not have the decals in stock, it is the racer's responsibility to obtain the proper decals to be eligible for Contingency payout.
WCHRA Point System:
We will be calculating points at each event, and will crown a champion at the conclusion of the season.
RACE DAY POLICIES:
SCALES:
After each qualifying and elimination pass, all cars must stop and weigh at the track scales. If you lose in eliminations and your opponent fails to make weight, you will be reinstated into the eliminations only if you made minimum weight requirements. If both cars failed to make minimum weight, both cars will be disqualified. It is the driver's responsibility to verify with each track scale, the weight of his/her car prior to each race day. There will be a 5lb error factor allowed.
TOW BACK & TOW VEHICLES
Drag Radial entries are allowed to tow to staging lanes and from the scales to the pits...No towing from the finish line to the scales! (Unless authorized by a WCHRA Official)
BYE-RUNS: Vehicles must take the tree, and run down the 1/8 mile. * Unless told otherwise by Race Director*
All drivers and vehicles must meet current NHRA and track requirements.
|
|
|
|